service air ride
Thread Starter
|
Junior Member
Joined: Feb 2010
Posts: 29
From: Sunny, South Carolina
service air ride
Well fellows I finally received my new air pump from Arnott Industries today ($192.00 shipped). Install was easy. What I had to do was, use factory wire connection plug, splicing new wires with old. I elected to solder wires then shrink wrap them. I also had to find a new bolt, nut and corresponding washers for the air dryer, the new Arnott did NOT have a threaded bracket like the factory orignal.
**A word of caution, When I disconnected the air line itself there is a U shaped plastic retainer. It was brittle and snapped in half. I used some small baling wire to temporarily hold it, I am heading to the dealer for a new this afternoon. The U retainer is not included in the Arnott kit (should be)!
After install started truck and no more "service air ride"
yippeee
**A word of caution, When I disconnected the air line itself there is a U shaped plastic retainer. It was brittle and snapped in half. I used some small baling wire to temporarily hold it, I am heading to the dealer for a new this afternoon. The U retainer is not included in the Arnott kit (should be)!
After install started truck and no more "service air ride"
yippeee
Member
Joined: Jan 2010
Posts: 40
From: Huntingdon Valley, PA
Well fellows I finally received my new air pump from Arnott Industries today ($192.00 shipped). Install was easy. What I had to do was, use factory wire connection plug, splicing new wires with old. I elected to solder wires then shrink wrap them. I also had to find a new bolt, nut and corresponding washers for the air dryer, the new Arnott did NOT have a threaded bracket like the factory orignal.
**A word of caution, When I disconnected the air line itself there is a U shaped plastic retainer. It was brittle and snapped in half. I used some small baling wire to temporarily hold it, I am heading to the dealer for a new this afternoon. The U retainer is not included in the Arnott kit (should be)!
After install started truck and no more "service air ride"
yippeee
**A word of caution, When I disconnected the air line itself there is a U shaped plastic retainer. It was brittle and snapped in half. I used some small baling wire to temporarily hold it, I am heading to the dealer for a new this afternoon. The U retainer is not included in the Arnott kit (should be)!
After install started truck and no more "service air ride"
yippeee
Thread Starter
|
Junior Member
Joined: Feb 2010
Posts: 29
From: Sunny, South Carolina
Carl, from start to finish about 1 1/2 hours. I should have taken pictures of the procedure and possibly asked for one of the mods here to FAQ them with full details. I was just to excited to install it. If anyone here evers asks I will redo the procedure and post pics if requested. That would take less than a half hour.
Member
Joined: Jan 2010
Posts: 40
From: Huntingdon Valley, PA
Carl, from start to finish about 1 1/2 hours. I should have taken pictures of the procedure and possibly asked for one of the mods here to FAQ them with full details. I was just to excited to install it. If anyone here evers asks I will redo the procedure and post pics if requested. That would take less than a half hour.
Thread
Thread Starter
Forum
Replies
Last Post
jmsnyder
Cadillac STS
8
Jun 5, 2021 06:41 AM
raceytracy
Suspension sponsored by Arnott Inc.
1
Feb 25, 2013 08:38 PM
jmsnyder
General Tech
0
Sep 11, 2012 11:03 PM
xpdude
Cadillac Deville
1
Oct 24, 2007 09:16 PM
Tiredtech
Cadillac Deville
2
Sep 8, 2006 02:28 AM
